Samsung SDI INR18650-35E 18650 Cell – 3500mAh 3.7V | Genuine Flat-Top Li-ion

₨ 1,100

Genuine Samsung SDI INR18650-35E high-energy 18650 Li-ion cell. Official datasheet specs: 3500mAh nominal, 3.6V, 8A max continuous discharge, ≤35mΩ impedance, flat-top unprotected. Built for e-bike, ESS, flashlight, laptop and moderate-current battery packs — not for vapes or high-drain power tools.

Price: ₨ 1100 per cell ·
WhatsApp us for bulk pack-cell quotations and custom battery assembly.

Description

Samsung SDI INR18650-35E — The Benchmark 18650 Energy Cell for Moderate-Current Packs

The Samsung SDI INR18650-35E is a genuine high-capacity 18650 lithium-ion cell designed for energy density and runtime, not extreme current draw. With an official datasheet rating of 3,500 mAh nominal capacity at 3.6 V, this cell is widely used in e-bike battery packs, ESS modules, flashlights, laptop packs, portable electronics and moderate-drain battery assemblies where watt-hours matter more than raw amps.

This is an unprotected flat-top cell. It has no internal protection circuit and must be used inside a properly designed battery pack with a compatible Battery Management System (BMS), fusing, insulation and mechanical support. Samsung SDI’s own laser marking on many OEM/pack versions includes the warning “FIRE HAZARD! NOT FOR VAPE!” — because the 35E is a capacity-optimised energy cell, not a high-drain power cell.

At Newon, we supply this cell for informed pack builders, repair technicians, e-bike converters, solar/ESS integrators and B2B buyers who understand the difference between an energy cell and a power cell. For high-drain applications such as mechanical vapes, heavy power tools or high-current motor loads, a 30Q-class or power-optimised cell is the correct choice — not the 35E.

Official Samsung SDI INR18650-35E Specifications

Parameter Official Value
Model Samsung SDI INR18650-35E
Manufacturer Samsung SDI
Chemistry LiNiCoAlO₂ / NCA-type, designated “INR”
Nominal Capacity 3,500 mAh
Minimum Capacity 3,350 mAh at 0.2C / 680 mA discharge
Rated Discharge Capacity ≥ 3,250 mAh at 1C / 3,400 mA
Nominal Voltage 3.6 V
Charging Voltage 4.2 V, CC-CV method
Standard Charge Current 1,700 mA
Max Charge Current 2,000 mA
Max Continuous Discharge 8 A
Max Pulse Discharge 13 A, non-continuous
Discharge Cut-off Voltage 2.65 V
Internal Impedance ≤ 35 mΩ, AC 1 kHz
Dimensions Diameter ≤ 18.55 mm, Height ≤ 65.25 mm
Weight ≤ 50 g
Operating Temperature Charge: 0°C to 45°C · Discharge: −10°C to 60°C
Cycle Life ≥ 60% capacity after 500 cycles, charge 1,020 mA / discharge 3,400 mA

Electrical Values

  • Nominal energy: 3.6 V × 3.5 Ah = 12.6 Wh per cell
  • Maximum continuous C-rate: 3 C
  • Pulse C-rate:   3.71C, short burst only
  • Heat at 8 A continuous: I²R = 8² × 0.035 Ω = 2.24 W per cell

The official continuous limit remains 8 A, and prudent pack design should keep long-duration loads below that with adequate airflow or thermal management.

Understanding the “+3400 mAh” Marking

Some genuine Samsung SDI 35E cells are marked +3400 mAh. This corresponds to the 1C test current used in the datasheet: 3,400 mA. Older or alternate production markings may show 3,500 mAh. Both refer to the same INR18650-35E family, with the official nominal capacity listed as 3,500 mAh and minimum capacity of 3,350 mAh under the specified 0.2C test condition.

Authenticity Checks Before Building a Pack

Counterfeit 18650 cells are common in grey-market supply. Before assembling any pack, verify the following:

  • Genuine factory wrap: authentic Samsung SDI 35E cells often appear with a pink/orange factory wrap on OEM or pack-use versions.
  • Laser markings: look for codes such as SDI R37T, +3400 mAh, and the safety warning FIRE HAZARD! NOT FOR VAPE!
  • Weight: genuine cells typically fall around 48–50 g. Cells materially below this range are suspicious.
  • Capacity test: genuine cells should hold at least 3,350 mAh under the specified 680 mA / 0.2C test condition.
  • Internal resistance: fresh genuine cells should measure ≤ 35 mΩ at AC 1 kHz.
  • Batch traceability: for bulk orders, request production lot codes and match cells by capacity, voltage and internal resistance before welding.

Correct Use Cases — and Where Not to Use the 35E

Best suited for

  • E-bike and e-scooter battery packs with moderate continuous current
  • ESS and stationary storage packs where energy density and cost per Wh matter
  • Flashlights and portable lighting using single-cell or small-series configurations
  • Laptop battery pack replacements and repair work
  • Power banks and portable electronics with moderate draw
  • UPS and telecom backup modules where current stays within safe limits

Pack Building Formulas Using 35E Cells

Nominal pack voltage = 3.6 V × Series count (S)
Full charge voltage = 4.2 V × S
Discharge cutoff voltage = 2.65 V × S
Pack capacity = 3.5 Ah × Parallel count (P)
Pack energy = 12.6 Wh × S × P
Max continuous pack current = 8 A × P

Common 35E Pack Configurations

Configuration Nominal Voltage Full Charge Cutoff Capacity Energy Max Continuous Current Typical Use
1S1P 3.6 V 4.2 V 2.65 V 3.5 Ah 12.6 Wh 8 A Flashlight, single-cell device
3S1P 10.8 V 12.6 V 7.95 V 3.5 Ah 37.8 Wh 8 A Small electronics, portable device
4S1P 14.4 V 16.8 V 10.6 V 3.5 Ah 50.4 Wh 8 A Power bank, small UPS, laptop-style pack
7S1P 25.2 V 29.4 V 18.55 V 3.5 Ah 88.2 Wh 8 A 24V-class control or light ESS pack
13S1P 46.8 V 54.6 V 34.45 V 3.5 Ah 163.8 Wh 8 A 48V e-bike / light EV, 1P only
4S10P 14.4 V 16.8 V 10.6 V 35 Ah 504 Wh 80 A High-energy portable station
13S10P 46.8 V 54.6 V 34.45 V 35 Ah 1,638 Wh 80 A 48V e-bike / light EV pack

Important Design Note: 8 A Is the Continuous Ceiling

The Samsung SDI datasheet lists 8 A maximum continuous discharge. That is not a suggestion — it is the thermal and electrochemical boundary for sustained operation. Pulse current of 13 A is allowed only for short, non-continuous bursts.

At 8 A, with ≤35 mΩ internal resistance, each cell can dissipate approximately 2.24 W. In a multi-cell pack, that heat must be removed. A sealed plastic enclosure with no airflow can cause temperature rise, capacity loss, venting or worse. For packs operating near the continuous limit, use:

  • Thermal pads or airflow where appropriate
  • Temperature sensors connected to the BMS
  • Current headroom in the BMS and wiring
  • Fusing sized to the pack architecture
  • Cell matching by internal resistance and capacity

Safety & Handling — Non-Negotiable

  • Unprotected flat-top cell: no internal protection circuit. External BMS mandatory.
  • Not for vapes: Samsung’s own warning marking states NOT FOR VAPE. Do not use in mechanical vape mods or high-drain vaping devices.
  • Never solder directly to the cell: use spot-welded nickel tabs or strips. Direct soldering can damage the seal and vent.
  • Charge only between 0°C and 45°C: never charge below 0°C due to lithium plating risk.
  • Discharge between −10°C and 60°C: low-temperature capacity and current capability will derate; confirm exact behaviour from the datasheet before winter-critical designs.
  • Respect cutoff voltages: charge to 4.2 V per cell, discharge cutoff 2.65 V per cell.
  • Use matched cells: same batch, similar OCV, similar internal resistance, similar capacity.
  • Do not mix chemistries or models: never combine 35E cells with other 18650 types in the same string.
  • Inspect for damage: torn wrap, dented casing, leaking electrolyte, unusual smell, heat or discolouration means stop use immediately.

Newon Custom Battery Support

A loose 18650 cell is not a finished battery. Newon’s Custom Battery Solutions service can design, match, weld, protect, fuse, test and deliver complete packs using genuine cells where appropriate. We also supply related components through the Solar & Energy Storage category.

For technical background on chemistry selection, read our LiFePO4 vs Li-ion Battery Cell Guide. For real pack-build examples, see Custom Battery Projects in Pakistan.

Frequently Asked Questions

Is the Samsung 35E a protected cell?

No. The Samsung SDI INR18650-35E is an unprotected flat-top lithium-ion cell. It has no internal protection circuit and must be used with an external BMS that provides overcharge, over-discharge, overcurrent, short-circuit and temperature protection.

Why does the cell say “NOT FOR VAPE”?

Because the 35E is a high-capacity energy cell, not a high-drain power cell. Vaping devices, especially mechanical mods, can demand currents that cause excessive heating, venting or fire risk in capacity-optimised cells. Samsung’s warning marking is a safety instruction, not marketing.

What is the maximum continuous discharge current?

The official datasheet lists 8 A maximum continuous discharge. Pulse current may reach 13 A for short, non-continuous bursts. Independent testing indicates significant heating above approximately 10 A, so prudent designs should stay at or below the 8 A continuous limit with proper thermal management.

What is the nominal voltage of the 35E?

The official Samsung SDI datasheet lists 3.6 V nominal. Some general Li-ion discussions round to 3.7 V, but for this cell the datasheet value is 3.6 V, with 4.2 V charge cutoff and 2.65 V discharge cutoff.

How many Wh does a 35E cell store?

Using the official datasheet values, nominal energy is approximately 3.6 V × 3.5 Ah = 12.6 Wh per cell. Real usable energy depends on discharge rate, temperature, age and cutoff voltage.

Can I use 35E cells in an e-bike battery?

Yes, for moderate-current e-bike or scooter packs where continuous per-cell current stays within safe limits. Many 48V architectures use 13S configurations. For high-current hubs or aggressive acceleration, a power-optimised cell such as 30Q-class may be more appropriate.

How do I verify genuine Samsung 35E cells?

Check for genuine factory wrap, laser markings such as SDI R37T and +3400 mAh, the NOT FOR VAPE warning, weight around 48–50 g, and capacity testing showing at least 3,350 mAh under the specified 680 mA condition. Counterfeits are common, so buy from traceable suppliers and test before packing.

What cycle life should I expect?

The datasheet states ≥60% capacity after 500 cycles under the specified test condition: charge 1,020 mA and discharge 3,400 mA. Real cycle life depends heavily on depth of discharge, temperature, current rate and charging discipline.


Disclaimer: Specifications are based on the Samsung SDI INR18650-35E product specification, Ver. 1.1, July 9, 2015, as supplied. Derived values such as nominal energy and C-rate are calculated from datasheet figures and are not separate manufacturer-published ratings unless stated. Real-world performance varies with production revision, cell age, storage history, temperature, charge/discharge rate, depth of discharge, BMS settings and pack design. This is an unprotected flat-top cell and requires a compatible external BMS, fusing, insulation, mechanical support and suitable charger. It is not for vapes or high-drain applications.  

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Samsung SDI INR18650-35E 18650 Cell – 3500mAh 3.7V | Genuine Flat-Top Li-ion”

Your email address will not be published. Required fields are marked *

Shipping & Delivery